Beeplog.com - FREE Blogs Create own Blog    Next Blog   


    battery area
 

Thursday, 15. April 2010

Choose a long life battery
By batteryarea01, 03:52

What is the wear of a battery when using? Is it a mechanical or chemical damage? In fact, it is indeed both. A battery is a perishable product that begins to deteriorate immediately after leaving the factory. Like a spring under tension, a battery seeks to return to its lowest denominator. The rapid aging of a battery depends on the depth of discharge, environmental conditions, methods used to load and procedures or lack of maintenance. The chemical composition of each battery is affected differently by aging and the use that actually,like the thinkpad r61 battery.


In Figure 1, we compare three batteries to be used in mobile communications and we study the chemical composition of each in terms of energy density, internal resistance, self-discharge and length of life expressed in cycles. To simplify the comparison of the internal resistance, we use d80 batterypacks 3.6 volts.


* The internal wiring, contacts and protection circuits are taken into account. Readings vary depending on the loading elements, the charge status and the number of elements connected in series

** The discharge is highest during the first 24 hours and decreases thereafter. Self-discharge increases with the age of the thinkpad t61 batteryand high temperatures.

*** The length of life cycles is based on the use and maintenance procedures. If we neglect to apply periodic full discharge cycles, the cycle can be reduced by a factor of three.

**** The lifetime cycles is based on depth of discharge. A shallow discharge produced over a deep discharge cycles.


Figure 1: Characteristics of Li-Ion, NiMH and NiCd thinkpad t61p series battery in terms of energy density, internal resistance, self-discharge and long life (life in cycles)


As part of an ongoing program of research to find the optimal system battery for wireless applications, Cadex has conducted tests on the life cycles on the batteries in nickel-cadmium (NiCad), nickel -Metal Hydride (NiMH) and lithium-ion (Li-ion) thinkpad t60 battery . All these tests were run on battery analyzers Cadex 7000 Series test laboratories Cadex Electronics Inc.. Vancouver, Canada.


The batteries were fully charged up front, and underwent a series of continuous cycles of charging and discharging. The internal resistance was measured by the method owner Cadex, the OhmTest. Self-discharge was obtained from time to time by noting the capacity loss incurred during a rest period of 48 hours. 53 batteries of different models and different chemical composition have been the subject of the testing program.


During the battery test laboratory, it should be noted that the yield obtained in a protected environment is usually greater than that obtained when the thinkpad z61p batteryis used in outdoors.


[Comment(s) (0) | Create comment | Permalink]


A solution to the mystery of the battery (A)
By batteryarea01, 03:50


As we move away from an analog phone now for digital phone, the Ibm thinkpad z61e battery is facing new demands. The analog equipment draws a current, while the digital telephone charges the battery by short and high voltage spikes. The satellite phone as used in Europe and Asia for example, draws 1.7 A of current when it transmits at maximum power. Figure 1 shows the typical capacitance load of phone GSN.


Figure 1: The standard wave moving GSN transmits voice into packets of 567 microseconds at a time of 4.61 milliseconds. The peak currents vary depending on signal strength and reach 1.7 amperes in fringe areas.


The low internal resistance is one of the most urgent needs for a digital cellular phone battery. Measured in milliohms (mO), the internal resistance is the controller of the thinkpad t60 battery, to a certain extent, determines the duration of the conversation. More resistance is low, the battery is less restricted by providing the necessary current spikes. A high reading of mO often turn indicator on a battery discharge apparently properly loaded, because the energy available can be fully furnished and remains in the battery.



In Figure 2, we study the cellular phone system in the world's most popular and compare the peak power and peak power requirements of the thinkpad t400 battery must provide. These systems are the GPA, the SNB, the TDMA and CDMA.



* Some phones are TDMA handset with dual-mode (analog load 800 mA DC, 1500 mA digital impulse load).
** The current varies depending on thinkpad r61e battery voltage: 3.6 V battery requires a higher current than a battery of 7.2 V.


Figure 2: The global cellular phone system and the needs of peak power.

[Comment(s) (0) | Create comment | Permalink]


Wednesday, 14. April 2010

How to increase the operating life of your cell phone
By batteryarea01, 04:03

During the previous few years, the periods of standby and conversation are much improved. The lithium-ion thinkpad t400 battery has doubled its energy density since its introduction in the early 1990s. In addition, large energy savings have been completed in the receiver circuits and the receiver. Figure 1 illustrates the reduction of energy consumption in these circuits since 2002. One must keep in mind that this applies only to economy Sleep and reception. The program requires approximately five times more energy compared to the reception and demodulation. The modern handsets have also enjoyed improved efficiencies in their emission systems.

Figure 1: Reduction of energy consumption. In addition to higher capacity, manufacturers of thinkpad r61e battery and cell phones have achieved significant economies of énergiedans circuits of the receiver and demodulator (Sieber and co., 2004).

This is not always the fault of the batteries

When the cell phone loose, the battery is often one that is criticized. The thinkpad x60s battery is the only part of a cell phone that is user replaceable and it becomes an easy target. Maintenance personnel often replace the box without testing, and all to fall on the same fault.

Change batteries in nickel lithium-ion batteries has eliminated many problems. Enclosures lithium-ion thinkpad x60 series battery are maintenance free They do not have this need periodic full discharge to restore capacity and there is no memory effect. Yet customers suspect the batteries as the reason for most problems. Consequently, large quantities of good boxes are replaced and discarded. This costs the cell phone industry tens of millions of dollars annually. The cell phone providers say that 90% of returned batteries could easily be repaired.


The technology is now available to test the PowerBook G4 battery with a quickly at a store, while the client patient. If replacement is necessary, an exchange is performed from a fleet of batteries that have already been repaired. The place restores eliminate shipping costs and frees manufacturers from the burden of having to process thousands of returned batteries.

Figure 2 illustrates the flow of conversation, starting with the client providing his cell phone, then check the battery and the provision of a replacement. The housing replacement is caught in a fleet of batteries that have already been refurbished with a battery analyzer. A recent pilot test conducted by a major service provider, using an exchange program, worked well and no battery replacement was never seen again because of a failure.

Figure 2: A cell phone is provided with a questionable battery. The battery is tested while the patient client. If it needs to be serviced, a box refurbished is exchanged with the client. The vgp-bps2c battery maintenance point of sale is making millions of savings to the industry and increasing customer satisfaction.

According to a U.S. supplier of cellular phones, a typical store averages receives ten batteries sent back a day. The treatment cost is estimated at U.S. $ 15 per package. This gives a total of $ 150 per day per store expense. Realizing the high costs and trying to make savings, ten stores participating in an experiment consisting of one month to examine and maintain the db-l40 batteryincoming using Cadex battery analyzers. During the duration of the study period, 1,981 stores were spared batteries, representing a saving of about $ 30,000.

[Comment(s) (0) | Create comment | Permalink]


When the battery has she been invented?
By batteryarea01, 04:02

One of the most important was discoveried in the last 400 years. You can ask the question: "Is that electricity from db-l20 battery has taken so long?" The answer is "yes" and perhaps much longer. But electricity did not become useful until the late 1800s.

The first method consisted of electricity from bn-vf823 battery to create a static charge. Alessandro Volta (1745-1827) invented a device known as the "electric gun" which consisted of a wire placed in a jar filled with methane in gaseous form. By sending an electrical spark through the wire, the jar began to explode.

Subsequently Volta thought of using this lp-e5 battery invention to attempt to provide long distance communications, but since the result is less successful course to send a single bit ... (Explosive!) An iron wire supported by wooden posts should be placed between Como and Milan in Italy. The wire to the other end, was to end in a jar filled with methane in gaseous form. At a given signal, an electrical spark should be sent by the wire and cause a detonation serving a coded event. This communications link was never built.

The next stage of electricity generation through electrolysis appeared. Volta discovered in 1800 that a continuous flow of electrical force was possible when using certain fluids to produce conducting a chemical reaction between metals. Moreover Volta realized that the tension increased when voltaic cells were stacked. This led to the invention of the nb-4l battery .

Since the experiments carried out were not only limited to a brief demonstration more spark lasting only a fraction of a second. A seemingly continuous flow of electric current was now available.

At the time, France was approaching a peak level of scientific progress and new ideas were welcomed with open arms to support the political agenda. By invitation, Volta addressed the French Institute in a series of conferences in which Napoleon Bonaparte participated. Napoleon, himself, offered his help in some experiments, creating sparks from np-40 battery , melting a steel wire, discharging a 'taser' and decomposing water into its constituent parts.

[Comment(s) (0) | Create comment | Permalink]


Tuesday, 13. April 2010

Using appropriate loading methods for your battery
By batteryarea01, 04:26

Much of the reliability and longevity of a battery depends on the quality of its charger. In a highly competitive market, shippers often have low priority, especially for consumer products. In this article, we conclude that the charger is essential and guarantees the protection of the compaq presario v2000 battery . We focus on methods recommended load to increase performance of battery packs NiCd, NiMH and Li-ion.

A battery should not become warm during charging because high temperatures shorten their life. However a certain temperature rise can not be avoided especially when charging batteries nickel. The temperature reached a peak when the battery reaches full charge, then reduced slightly when the Compaq Presario V4000 battery goes into charge mode at low speeds. The battery should eventually return to room temperature.

If the temperature remains consistently above the ambient temperature after a few hours in a ready mode, the charger does not work correctly. Remove the battery when it is ready for any prolonged trickle charging will damage the battery. This warning applies especially to NiMH Apple PowerBook G4 battery,because this chemical does not absorb much torque overload.

A lithium battery should never become warm during charging. If this occurs, the battery or charger is defective. Stop using them.

Chargers nickel are grouped into three categories:

Slow charger - The slow charger, also known as the 'overnight charger', applies a fixed charge of about 0.1 C * (one tenth of the nominal capacity) until the battery is connected. The charging time is 14 to 16 hours. The slow chargers come with cordless phones, CD players and portable consumer products.

Quasi-fast charger - The quasi-fast charger has a place in the middle range, both in terms of charging time and price. Charging takes between 3 and 6 hours and theAcer aspire 3000 battery switches to trickle charge when it is in state 'ready'. Quasi-fast chargers accommodate a Nickel or lithium and those are used with professional products such as cellular phones, laptops and camcorders.

Quick Charger - This charger offers several advantages, the most obvious one is load duration smaller. At 1C, a flat apple a1185 battery NiCd or NiMH usually loads in less than an hour. Accurate detection of full charge is important. Once the battery is fully charged, the charger switches to regime filler then trickle. The rapid chargers are used with industrial equipment such as transmitters - receivers, medical equipment and portable tools.

Simple guidelines:

-A charger designed for NiMH HP Pavilion ZV6000 battery can also accommodate NiCd, but the reverse is not true. A charger designed for NiCd NiMH battery overload.

The nickel-battery fast charging prefer because it reduces the crystalline formation (a process known as "memory")

The nickel-and lithium batteries require different charge algorithms. These two couples chemicals are not normally interchangeable on the same charger.

If she is not used so often, remove the battery from its charger and use a filler before use. Do not leave the vgp-bps2c battery in standby mode in the charger.

[Comment(s) (0) | Create comment | Permalink]


The testers for modern batteries
By batteryarea01, 04:25

Rechargeable batteries have a reputation for causing most concern, such as Dell inspiron 1721 battery,disappointment and frustration than any other part of a portable device. Considering its relatively short life, the battery component is also the most expensive and least reliable.

How do we proceed to the verification and maintenance of batteries? This article describes the technical progress made by modern battery analyzers, and how these devices are used in industry. Organizations such as Public Safety use battery analyzers for several decades to restore and extend the life of nickel-cadmium Dell inspiron 1520 battery, however, battery analyzers are increasingly used in mobile phone market. The old models are not practical and could not adapt to the rapid development of new types of batteries. In addition, the analyzers were complex and they often were fast and precise as required by customers.

In recent years, there has been an important evolution in technological development in the field of battery analyzers. Devices that allow only apply cycles on theDell inspiron 1525 battery were removed from the market. In moving from a Nickel-intensive maintenance for lithium batteries no longer requiring periodic discharges, the battery analyzer was used to prolong battery life is now used for the rapid verification and rapid repair of batteries.

There are two basic types of battery analyzers: those with fixed current and those that are programmable. While fixed current analyzers are cheaper and generally easier to use, programmable analyzers are more accurate and faster. The programmable devices can be adapted more easily to different types of batteries and they can more effectively restore weak batteries. Only programmable analyzers allow rapid testing of Dell inspiron 5100 battery .

From a technical standpoint, both types of analyzers function as follows: When inserting a battery in an analyzer fixed current maintenance is performed using a fixed current to charge and discharge of approximately 600 mA. The maintenance of small batteries is done fairly quickly, while that of large batteries is slow. The duration of maintenance of a 1800 mAh compaq presario m2000 battery is three times longer than a battery of 600 mAh. The reading takes place in mAh capacity and reflects the duration of discharge. For cons, the analyzers perform programmable maintenance of batteries according to predetermined parameters. The reading is usually a percentage of the rated capacity of the battery.

[Comment(s) (0) | Create comment | Permalink]


Using appropriate loading methods for your battery
By batteryarea01, 04:23

Much of the reliability and longevity of a battery depends on the quality of its charger. In a highly competitive market, shippers often have low priority, especially for consumer products. In this article, we conclude that the charger is essential and guarantees the protection of the compaq presario v2000 battery . We focus on methods recommended load to increase performance of battery packs NiCd, NiMH and Li-ion.

A battery should not become warm during charging because high temperatures shorten their life. However a certain temperature rise can not be avoided especially when charging batteries nickel. The temperature reached a peak when the battery reaches full charge, then reduced slightly when the Compaq Presario V4000 battery goes into charge mode at low speeds. The battery should eventually return to room temperature.

If the temperature remains consistently above the ambient temperature after a few hours in a ready mode, the charger does not work correctly. Remove the battery when it is ready for any prolonged trickle charging will damage the battery. This warning applies especially to NiMH Apple PowerBook G4 battery,because this chemical does not absorb much torque overload.

A lithium battery should never become warm during charging. If this occurs, the battery or charger is defective. Stop using them.

Chargers nickel are grouped into three categories:

Slow charger - The slow charger, also known as the 'overnight charger', applies a fixed charge of about 0.1 C * (one tenth of the nominal capacity) until the battery is connected. The charging time is 14 to 16 hours. The slow chargers come with cordless phones, CD players and portable consumer products.

Quasi-fast charger - The quasi-fast charger has a place in the middle range, both in terms of charging time and price. Charging takes between 3 and 6 hours and theAcer aspire 3000 battery switches to trickle charge when it is in state 'ready'. Quasi-fast chargers accommodate a Nickel or lithium and those are used with professional products such as cellular phones, laptops and camcorders.

Quick Charger - This charger offers several advantages, the most obvious one is load duration smaller. At 1C, a flat apple a1185 battery NiCd or NiMH usually loads in less than an hour. Accurate detection of full charge is important. Once the battery is fully charged, the charger switches to regime filler then trickle. The rapid chargers are used with industrial equipment such as transmitters - receivers, medical equipment and portable tools.

Simple guidelines:

-A charger designed for NiMH HP Pavilion ZV6000 battery can also accommodate NiCd, but the reverse is not true. A charger designed for NiCd NiMH battery overload.

The nickel-battery fast charging prefer because it reduces the crystalline formation (a process known as "memory")

The nickel-and lithium batteries require different charge algorithms. These two couples chemicals are not normally interchangeable on the same charger.

If she is not used so often, remove the battery from its charger and use a filler before use. Do not leave the vgp-bps2c battery in standby mode in the charger.

[Comment(s) (0) | Create comment | Permalink]


Saturday, 10. April 2010

Breakthrough in the rapid test batteries
By batteryarea01, 04:11

When I asked a leading manufacturer of batteries: "Is it possible to perform a quick test of inspiron 1525 battery?" The engineer replied with a "NO" categorical. He based his conclusions on the difficulty of using a universal test that would apply to all uses of batteries ranging from wireless communications to mobile computing, mobile tools for lifting and electric vehicles.

Several universities and private companies, which include Cadex Electronics, trying to find a viable solution for rapid testing of inspiron 1501 battery . Many methods have been tried and a roughly equal number have failed due to a lack of precision and practicality.

In studying the characteristics relating to health (SoH) and the state of charge (SoC) of batteries, we can observe interesting effects. Unfortunately these properties are "heavy" and not linear, and even more importantly, the parameters are unique to each type of inspiron 5100 battery . This inherent complexity makes it difficult to create a formula that works for all batteries.

Despite these seemingly insurmountable difficulties, the rapid test batteries is nevertheless possible. But the question is: "How can one be both precise and universal for couples chemical compaq presario m2000 battery changing?". The cost of an early commercial tester is also a problem.

The secret of the rapid test batteries lies in the understanding of the use of battery power. The compaq presario v2000 battery charges vary from short current spikes for a GSM phone to intermittent heavy loads for mobile devices, calls continuous power for laptops.

The first step to achieving results in a quick test is to measure the internal resistance of the battery, often referred as qu'impédance. The impedance measurements take just seconds to unfold and provide a reasonably accurate indication of Compaq Presario V4000 battery status, especially if a reference indication of a good battery is available as a comparison.

Unfortunately, the impedance measurement alone provides only a rough picture of the performance of the battery . The results are affected by various states of the battery that can not always be controlled. For example, a fully charged PowerBook G4 battery that has just been withdrawn from a magazine shows an indication of higher impedance than that which has remained at rest for a few hours after charging. The high impedance is due to electrochemical noise present after the load. Let the battery sit for an hour or two to allow the battery to "normalize". The temperature also affects the results. In addition, chemical composition, the number of elements connected in series and rated current (Ah) battery influence the results. Many batteries also contain a protection circuit which distorts the results even more.

[Comment(s) (0) | Create comment | Permalink]


How to discover the true health of your battery?
By batteryarea01, 04:08

The test of AC conductivity was introduced in 1992 as a new way of measuring the CCA (Cold Cranking Amps = Current cold start) of a car battery. This non-disruptive method has been acclaimed and regarded as a breakthrough and, to a large extent, eliminates the discharge test to measure the performance of the a1185 battery . The test only takes a few seconds, the readings are displayed as digital numbers and a message indicating the status of the battery. There is no spark occurs at the terminals of the battery and the instrument does not heat.

But the single frequency AC conductance has its limitations. It does not measure the CSF according to SAE standards and provides an approximation about the power of the Pavilion ZV5000 battery can provide energy (output). The figure on how much energy often varies with the state of charge (SOC = State of Charge), and other battery conditions. Sometimes, a good battery fails and one that is defective passes the test but by mistake. But his most important drawback is the inability to perform the reading of the reserve capacity (RC). Despite these shortcomings, the AC conductance has become an accepted standard for predicting the lifetime of the battery and to determine when to replace an old battery before it causes you problems.

Figure 1: Battery with high CCA and reserve capacity of 100%.such as pavilion zv6000 battery. A battery with a CCA rate may be compared to a large open tap that allows a free flow. What are the main differences between the parameters CCA and RC? A high reading of CCA provides good conductivity of the battery and provides a high capacity / ability to boot. A high CSF is associated with a low internal resistance of the battery. Figure 1 compares high CCA with a large open tap that allows a free flow.

The reserve capacity governs the amount of energy a battery can accumulate. A new aspire 3000 battery is indicated by the manufacturer as having a nominal capacity of 100%. When the battery gets older, the reserve capacity drops and eventually it needs to be replaced when the reserve capacity falls below 70%. Reading RC always refers to a fully charged battery, the state of charge (SoC) should have no effect on the measure.

It is possible that a battery provides a good reading of CCA and starts well a vehicle while having a low reserve capacity. But the latitude d630 battery will discharge rapidly if we tried to extract extra energy (eg. For accessories). Figure 2 illustrates such a battery. The so-called "content rocky" which accumulates when the battery ages is permanent and this process is irreversible.

Figure 2: Battery with high CCA but a low reserve capacity. Starting with this battery is good but a withdrawal of additional energy will drain the battery quickly

[Comment(s) (0) | Create comment | Permalink]


Friday, 09. April 2010

The development of lithium
By batteryarea01, 04:19

Investors got benefit from this development with investment in lithium. Many individual stocks is already priced into the boom, however,Mobile phones, laptops or cordless screwdriver - almost everywhere, where electrical energy is used and the go mobile, with lithium is in the game. The alkali metal is the basic raw material for lithium-ion hp pavilion dv4000 battery dar. These high-performance batteries will in future also increasingly drive hybrid and electric vehicles. Because compared to other battery types, the lithium-ion version is considered the most efficient. In addition, it has hardly called memory effect. This means the degradation of a battery when it is repeatedly only partially discharged and recharged.

Consequently, almost all auto-or battery manufacturers use in their drive concepts for hybrid and electric vehicles on the lithium-ion xps m1730 battery technology. This should have increased the demand for the alloy in the coming years strong. For the spread of hybrid and pure electric vehicles is expected to increase significantly. Already being advertised for customers no longer primarily concerned with horsepower, but drive with eco-friendly concepts. Of more and more vehicle models, there is now or in the near future, a hybrid version. Almost everywhere at once pure electric vehicles are developed. Mitsubishi sold in Japan with the i-MiEV the first exclusively equipped with an electric car that is produced in batches. The sale is expected to increase within two years from 8500 to 30 000 units - so the plan.

Besides Japan, set mainly the U.S. and China to the massive spread of the new drive Ibm thinkpad r50p battery technology. The purchase of an electric vehicle in the United States, the equivalent of Euro 5800 is eligible. In the People's Republic, the corresponding subsidy amount even at 6700 Euro. Both countries want to reduce their dependence on fossil fuels. Moreover, the two largest nations of the world car set a target for the key technology for future generations the very front car to be there.

The government in China is planning, in 20 years, 80 percent of the electric car sold in China come from domestic production. In particular, the short-haul traffic in big cities is suitable for electric vehicles. The rapidly growing urbanization of China offers the best conditions for the new drive concepts. Already today in the Middle Kingdom more electric bikes sold than in any other country on earth. The move to the electric car seems to be only logical. In the U.S., in addition to shaking, the sudden rise in oil prices in mid-2008 politics, business and consumers.

The Boston Consulting Group estimates that in ten years in China, Japan, USA and Western Europe is driven in every four new cars from a hybrid or electric motor. The market for lithium-ion Ibm thinkpad r50e battery is to more than triple - to a sales volume of more then 25 billion dollars a year.

Looking ahead, as the stock market is already anticipating this development was a long way away. For example, the units of the Chinese manufacturer of lithium-ion battery Build Your Dream (BYD), almost seven-fold since early 2009. There is a fear that has formed in the battery producers assess bladder. In addition, cavort in the industry, dozens of smaller companies, of which not all can cope with the enormous investment needs. As with the Internet, despite the anticipated boom in lithium-ion Ibm thinkpad r50 series battery with serious imbalances and bankruptcies expected of individual companies. Those who join right now, so is taking a certain risk.

Therefore seems more promising to invest in the issue of electric mobility by way of the light metal lithium. By far the world's largest producer Sociedad Quimica y Minera de Chile (SQM) is. The Chilean mining and chemical company supports almost one third of the global lithium Ibm thinkpad t42 battery production. However, the alkali metal in SQM is "only as a byproduct, not even contributes to ten percent of sales. There is also an investment in SQM, the single value of risk. To avoid this, it makes sense to distribute an investment on a large number of companies exploring the lithium or already promote.

If that is too complicated, can resort to appropriate baskets or ETFs, which are offered on the Lenovo thinkpad r61i series battery market. This should look at a long term, since it also can lead to short-term excesses to the top, but also down. Because each individual lithium-shares differ widely, actively managed products is to be preferred.

The ethical and ecologically sound investment, however, is to look for when buying a car next to exhaust emissions and invest in a hybrid vehicle.

[Comment(s) (0) | Create comment | Permalink]


The mobile phones batteries
By batteryarea01, 04:17

With the start of spring back first cyclist to be seen, which can take much of their home electronics on tour scheinen.Vieles like it but after a few hours can no longer use ,because of theLenovo thinkpad t61p series battery haben.Helfen schlappgemacht E-factory (139 euros) from Busch & Müller, the liefert.Der while cycling power small, 50 gram box decreases power by all standard bicycle dynamo hubs and delivers it to MP3 players, cell phones, GPS receiver, but also cameras and lighting tent. The product identifier plant is certainly a little too bold, but still delivers the box up to 16 Watt.Im test I could phone to provide mini-computer and navigation system problems with electricity.

By early spring, again first cyclist to be seen, which seem to take much of their home electronics on tour. Much of it can, however, after a few hours can no longer use because the thinkpad x60 series battery have schlappgemacht. Help to the charger E-Werk (139 euros) from Busch & Müller, which supplies electricity while cycling.

The small, 50 gram box decreases power from all major bicycle hub dynamo and delivers it to MP3 players, cell phones battery(like the Lenovo thinkpad r61e battery) , GPS receivers, as well as cameras and lighting tent. The product identifier plant is certainly a little too bold, but still delivers the box up to 16 watts.

In the test I could phone to provide mini-computer and navigation system problems with electricity from ibm thinkpad x60s battery . Very closely you can adjust the voltage from 2.8 to 13.3 volts and the amperage from 0.1 to 1.5 amps.

Here the user can not commit errors, otherwise the electronics within the phone on for ever their work. , I have accurately quoted me in advance what values are on the transformer plugs of terminals. Then just have the correct value with two rotary switches are set in the pits. Sounds simple, but it was not: The scale is difficult to detect in the dim light, almost not at all. Another problem:the power of Some laptop are not sufficient ,which is from Lenovo thinkpad r61 battery , they also need a connection to the computer. The e-work can not charge the iPhone.

My fear, I would have during the test drive through Berlin ignore all traffic rules and risk my life in order to produce sufficient amount of power was unnecessary. Even at a pace as more parents with their strollers passing by me, had been running the empty sony vgp-bps2c of the MP3 player sounds first of himself. After 20 minutes at 15 kilometers per hour, the E-works had charged the phone battery to ten percent. And that is certainly no speed for racers.

Law is simply the assembly. When I saw are the many parts of me, I have several hours to set screws, but it actually went very quickly - and usually without tool. In addition to the cables for the lighting system was still space on the dynamo, to secure the E-works with O-rings made of rubber and the cable with a binder to the frame. The heavy rain during the test drive had something good, I was able to convince me that the cable glands are waterproof.

[Comment(s) (0) | Create comment | Permalink]


Wednesday, 07. April 2010

Sharp produce solar cells with STMicroelectronics joint venture
By batteryarea01, 04:46

According to reports, STMicroelectronics, Sharp and Enel Group, a subsidiary of Enel Green Power announced that it would form a joint venture in Italy to produce thin-film solar Dell latitude d600 battery .


Sharp plans to extend the clean energy business, and reduce production costs. Sharp and the Italian utility company Enel in 2008 announced its intention to produce thin-film solar Dell inspiron 1721 battery with European manufacturers , but it did not specify which company.


Sharp said in a statement, in addition to bank loans, the joint venture of the three investors will investe to the solar Dell inspiron e1505 battery project of up to 70 million euros. Three investors will each hold one-third of the joint venture interests.


The joint venture plans to begin early in 2011 STMicroelectronics plant in Sicily, solar Dell latitude d510 battery, an initial annual capacity is 160 megawatts, and then gradually increase to 480 MW.Sharp and Enel Green Power will set up another joint venture, using the above joint venture to produce solar panels to generate electricity. Sharp said that before the end of 2016, its joint venture with Enel Green Power's total capacity will exceed 500 MW power plant.

[Comment(s) (0) | Create comment | Permalink]


South Korea's LG enter into the solar cell area
By batteryarea01, 04:43

South Korea's LG started to produce solar Dell inspiron 6400 battery in January 2010. It is understood that, LG's solar-cell factory in the first year,is based in Seoul, near the turtle tail, will mainly produce crystalline silicon solar cells, and output up to 520,000 battery components, a total of 12 million kilowatts of capacity, it is equivalent to 4000 electricity required for the average family household. The second branch is expected in 2011.


Although the capacity of solar energy equipment is over, South Korea famous home appliance companies still want a slice in the market. In fact, LG, when in July of this year, there was a launch of an allegedly the world's most energy-efficient thin-film solar Dell inspiron 1520 battery (solar energy conversion rate of 11.1%).In addition, solar panels and LCD TV market outlook is very similar. This is the main reason why South Korean electronics giant - LG Electronics and Samsung have decided to extend its business for solar cell.


In recent years, Korean solar panels in the domestic market share has continued to rise. Statistics showed that South Korea's output of solar Dell vostro 1400 batteryin 2008 reached 274,000 kilowatts, it almost six times than the previous year.


LG and Samsung increasly emphasis on green R & D and sales of electrical appliances, the two companies has introduced its own product under the banner of water-saving, energy-saving,Samsung is even crazily sad that emissed carbon dioxide by 50% on the basis of regular HP Pavilion ZV6000 battery sales to 2013 through improving processes and promote their products

[Comment(s) (0) | Create comment | Permalink]


Saturday, 03. April 2010

Tips to maximize battery run-time
By batteryarea01, 04:12


Netbook users are much more than PC users, so for them the power consumption of the equipment and the stamina of the Batteries so important. If an outlet is close by and you work too long or surfing, it can quickly become too dark for a short duration on the screen. How can something this time herauszögern further, the magazine colleagues tested the laptop and have come to interesting results. The extent to which Reviews are feasible even for one depends on the tolerance but from opposite reading comfort and system performance. The tests were unfortunately not with a Netbook, but with a Toshiba Satellite M505 with Intel Core performed i3, whose normal inspiron 1520 batterylife of 3 hours and 11 minutes was.


The processor offers little potential for power saving


The inspiron 6400 battery consumption of the processor can not further reduce the test that. In the menu Settings -> CPU can minimize the performance, but takes a slower processing speed - in the test than 25 percent - and is still buying in even less power than three minutes duration.


Were tested three more opportunities for power from latitude d820 battery saving, which were much more successful in the execution. The best known version is probably the trick with the screen lighting. This can be from 40 percent in energy saving mode to reduce to 0 percent, or off entirely. Still, the ads are still readable. With the light trick the testers gained in using the M505 eleven minutes longer useful life.


Less light brings the most


Even more efficient in terms of Pavilion ZV6000 battery makes to the OS Windows 7 disabling the graphical effects. Switching off the enhanced graphics Aero Glass - but the Starter Edition to most netbooks anyway does not exist - and the display mode from Aero Peek, one can work 19 minutes longer. However, with disabling drop off some attractive features and the surface looks more like Windows XP than in Windows.


Most of time the mobile work could win with the last trick. By a simple trick can reduce the light pixels displayed on the screen. Personalized the representation so that the contrast reversed and therefore as many areas are displayed in black instead of white. Thus, the latitude d600 batterycould survive in the test 25 minutes longer. Here, too, must respond to compromises, because reading white text on black background is at least used to. The conversion is done by right-clicking on the desktop. It is then necessary to change the design to Windows Classic, only then will the opportunity to select Contrast Black. Here, the features of Aero Glass and Aero Peek go right with flutes and the design is, of course, kind words, very old school.


Sorry, no addition of the effects


All add up the savings along the way, not time gains, but would also even at 19 minutes. Most efficient is to focus on the contrast setting. On the tips of the laptop magazine out there are still other ways too familiar. That is about how to disable WLAN, Bluetooth and UMTSIf this is not needed. Even USB drives and memory cards should be deducted, if not just access it needs. Unnecessary services and processes in the background can also be turned off. And it saves the most electricity from vostro 1400 battery in the rest, if instead of 15 minutes surfing the Internet procrastination time reading a newspaper or something just looks out the window.

[Comment(s) (0) | Create comment | Permalink]


Acer Aspire One 532 netbook with a longer duration
By batteryarea01, 04:09

The Taiwanese hardware manufacturer Acer announced the launch of two new netbook models, such as the tech-blog mobicroco reported. The Acer Aspire One 532 is equipped with a new technique that the Accumulator hold up to one fifth of the recent Betriebsszeit longer can. The platform combines Pinetrail this memory and graphics controller, which produces not only a longer inspiron e1505 batterylife, but as another side effect of a 15 - percent improvement the processor system performance results. Thus, this model is ideal for long trips or other forms of electricity dry spells.


The other dimensions also speak to a travel companion. A 10.1-inchDisplay can either be ordered in HD or matt. The netbook is only 2.5 centimeters thick and weighs a kilo. and its inspiron 6000 battery is also very thin . Wireless internet is available for connection and the internal memory capacity of 2 GB holds ready. This model is priced in the moderate range with 299 euros for the standard version with the matte display and 349 euros if it is to be an HD display.


4 GB internal storage


About the price of the Acer Aspire Time Line x 1830T is yet known, he is expected to be announced until the last week of March. This netbook features even on a good battery performance with up to eight hours,like the latitude d510 battery,but it remains below the Aspire 532nd Unbeatable however, is the storage capability. The internal RAM memory of 2 GB can be doubled and thus allows, movies or other media files on the move to have handy. For those who like the netbook more surfing To use, the device offers WLAN in b / g / n, Gigabit Lan and three USB ports, as well as other Bluetooth 2.1 connectivity. At the request and probably with extra charge, it is also available in a 3G module.


How to get a new netbook: Step by Step


Teltarif has a Checklist created, read in is what matters at the Netbook and what to consider when buying.certaily its inspiron 6400 battery is very important The desired model is found out that simply in the Netbook database by teltarif.de.


[Comment(s) (0) | Create comment | Permalink]


Next page »

FREE Blog at Beeplog.com
Responsible for the content of the member blogs are our members, not the provider, Beepworld GmbH

 


Navigation
 · Startpage

Login / Administration
 · Login!

Calendar
« December, 2014 »
Mo Tu We Th Fr Sa Su
1234567
891011121314
15161718192021
22232425262728
293031    

Categories
 · All entries
 · camera news (18)
 · common sense (10)
 · General (10)
 · tips (1)

Links
 · Free Blog

RSS Feed